2.0 TSI EA888 Open Air Intake suction with TÜV BAR-TEK®

One of the best intakes for the 2.0L & 1.8L TSI engine with TÜV! One of the best and alsowith TÜV: Our Open Air Intake for Golf 7, Golf 8 and Co is the right thing for you if you are looking for arich soundandsignificantly more power! This suction was developed on our performance test bench for maximum performance. With our new suction, we have found a way to supply your turbocharger with even more fresh intake air. Thanks to the optimised design, the air flow to the compressor is completely undisturbed and also increased, so your turbo has plenty of fresh air to work with. Your engine will thank you for thiswith up to 25 hp more power and 20 Nm more torquecompared to the standard intake! We have also ensured that the intake air not only flows in abundance, but is also nice andcool: thanks to the integrated heat shield, the performance air filter always draws in cold air, whichfurther optimises combustion. If you think an open mushroom sucks in warm air and is counterproductive, I have to tell you quite clearly that it is not! It is not! The warm air in the engine compartment is completely sucked away within a second. And then there is only cool, fresh intake air! Freshly developed by the Head of Boost: open 2.0 TSI EA888 suction for +25 hp When it comes to new performance products, we spare no expense and no effort and our open performance suction is no exception. We wanted to develop anair intake systemthat reduces the restrictions as much as possible so that the air reaches the turbosmoothly. Standard air filtersare designed to prevent clogging under a wide range of conditions and reduce intake noise. From a performance perspective, this makes them veryinefficientand their sound is boring. We have changed both! We were able to reduce the pressure drop and increase the flow rate at the same time to give youmaximum performance. Depending on the vehicle, you can achieve up to 25 hp more power and 20 Nm more torque. The sound is also no longer restricted with our open suction and the result is abeastly good sound. The features of our open air intake: with TÜV for all Golf 7 and Golf 8 series Filter in blue or black Up to 25 per cent more power hp Up to 20 Nm more torque Optimised design Increased throughput Heat protection for air filter cool intake air Developed on the dynamometer No error message Plug and play Open Air Intake made of PA 6.6: The stuff intake dreams are made of!When choosing the material, we also considered the highest possible performance and therefore opted for the famous PA 6.6, which is also known as nylon 66. It is the polyamide with thebest properties at high temperatures over a long period of time, starting with great hardness, rigidity, abrasion resistance and dimensional stability. It also has excellent sliding and friction properties, making it theperfect materialfor our suction.These are the main characteristics of PA 6.6:good sliding and friction propertieshigh abrasion resistanceelectrically insulatinggood wear resistancegood weldability and bondabilityhigh strengthresistant to many oils, greases and fuelshigh toughness and very lightYou can download the vehicles approved by TÜV here!Please send us your VIN (chassis number) for your personalised certificate.In our video (below) Bartek shows you personally how quickly the suction is installed!For engines with a mass air flow sensor, please refer to the last picture for installation (no extra parts required).It is also possible to fit the LMM with a76mm silicone hoseto connect. See below at accesories.- Made with ❤ - Open Air Intake made of PA 6.6: The stuff intake dreams are made of! When choosing the material, we also considered the highest possible performance and therefore opted for the famous PA 6.6, which is also known as nylon 66. It is the polyamide with thebest properties at high temperatures over a long period of time, starting with great hardness, rigidity, abrasion resistance and dimensional stability. It also has excellent sliding and friction properties, making it theperfect materialfor our suction. These are the main characteristics of PA 6.6: good sliding and friction properties high abrasion resistance electrically insulating good wear resistance good weldability and bondability high strength resistant to many oils, greases and fuels high toughness and very light You can download the vehicles approved by TÜV here!Please send us your VIN (chassis number) for your personalised certificate.In our video (below) Bartek shows you personally how quickly the suction is installed!For engines with a mass air flow sensor, please refer to the last picture for installation (no extra parts required).It is also possible to fit the LMM with a76mm silicone hoseto connect. See below at accesories. You can download the vehicles approved by TÜV here! Please send us your VIN (chassis number) for your personalised certificate.In our video (below) Bartek shows you personally how quickly the suction is installed! For engines with a mass air flow sensor, please refer to the last picture for installation (no extra parts required). It is also possible to fit the LMM with a76mm silicone hoseto connect. See below at accesories. - Made with ❤ -